#
# this config file was automatically generated
# using lirc-0.6.3(parallel) on Mon May 28 22:48:24 2001
#
# contributed by  Jordan Hazen <jnh@aug.com>
#
# brand:             JVC
# model:             HR-S7600U SVHS VCR
#
# most of these codes are shared amongst all recent-model JVC VCRs.  These
# represent code set "A"... I couldn't get set "B" to work reliably

begin remote

  name  jvc
  bits            8
  flags SPACE_ENC|CONST_LENGTH
  eps            30
  aeps          100

  one           637  1513
  zero          637   441
  ptrail        636
  pre_data_bits   8
  pre_data       0xC2
#  gap          46280
  gap          35000
  min_repeat      1
  toggle_bit      0


      begin codes
	'1'                   0x0000000000000084    # 1
	'2'                   0x0000000000000044    # 2
	'3'                   0x00000000000000C4    # 3
	'4'                   0x0000000000000024    # 4
	'5'                   0x00000000000000A4    # 5
	'6'                   0x0000000000000064    # 6
	'7'                   0x00000000000000E4    # 7
	'8'                   0x0000000000000014    # 8
	'9'                   0x0000000000000094    # 9
	'0'                   0x00000000000000CC    # 0
	'ENTER'               0x000000000000007C    # enter
	'LINE'                0x0000000000000076    # line
	'UP'                  0x0000000000000098    # up
	'DOWN'                0x0000000000000018    # down
	'PLAY'                0x0000000000000030    # play
	'PAUSE'               0x00000000000000B0    # pause
	'STOP'                0x00000000000000C0    # stop
	'REWIND'              0x00000000000000E0    # rewind
	'FF'                  0x0000000000000060    # ff
	'FWD'                 0x0000000000000028    # fwd
	'BACK'                0x00000000000000A8    # back
	'RECORD'              0x0000000000000033    # record
	'SKIP'                0x0000000000000069    # skip
	'MENU'                0x00000000000000EC    # menu
	'DISPLAY'             0x000000000000001C    # display
	'RESET'               0x000000000000006C    # reset
	'CHECK'               0x00000000000000BC    # check
	'POWER'               0x00000000000000D0    # power
	'EJECT'               0x0000000000000020    # eject
	'SPEED'               0x000000000000008C    # speed
	'TIMER'               0x00000000000000AC    # timer
	'PROGRAM'             0x0000000000000083    # program
	'OK'                  0x000000000000003C    # ok
	'START+'              0x0000000000000013    # start+
	'START-'              0x0000000000000093    # start-
	'STOP+'               0x0000000000000053    # stop+
	'STOP-'               0x00000000000000D3    # stop-
	'DATE+'               0x0000000000000063    # date+
	'DATE-'               0x00000000000000E3    # date-
	'CHANNELUP'           0x0000000000000098    # ch+
	'CHANNELDOWN'         0x0000000000000018    # ch-
      end codes

end remote
